|
 |
|
|
| CT-3500 Digital Circuit Breaker Analyzer |
 |
 |
- More accurate than Mechanical-Cycle Counters
- Far exceeds the power utility industry's requirement for accuracy
- No Conversion Calculation Required; Timing Results Display in Milliseconds & Cycles
- Timing Results from all three Timers are shown Simultaneously on a Backlit LCD
- Backlit LCD for easy data readout in bright sunlight outside or inside
- Fully analyzes all breaker operation: Open, Close, Open-Close, Close-Open
- Stores 128 Timing Records
- Built-in 2.5" Thermal Printer
|
The CT-3500 is a second generation, stand-alone, digital, microprocessor-controlled, circuit breaker timer. It measures elapsed time from the instant a breaker coil is powered to the instant of opening or closing of a circuit-breaker's dry contacts. The CT-3500 not only times the breaker's contact response time, but it can also time relays or other switching function that uses an initiating-trigger voltage (24-300 Volts dc or ac) |
|
| CT-6500/S2 Digital Circuit Breaker Analyzer |
 |
|
- Full Breaker Tabulated & Graphic Data Printout
- Detect Main & Insertion Resistor Contacts on same input
- Digital Travel Transducer; no setup or calibration needed
- Diagnostic ability
- RS-232C and USB computer interfaces
- Store 100 timing records
- Initiate Breaker Operation
- Built-in Thermal Printer
|
The Model CT-6500 Series 2 is a stand-alone, microcomputer-driven EHV Circuit-Breaker Analyzer. It is inexpensive and easy to use. The CT-6500 is available in models with either 3 dry contacts (CT-6500-3); 6 dry-contacts (CT-6500-6); or 12 dry-contact inputs (CT-6500-12). The CT-6500 fully analyzes circuit-breaker performance: contact time, stroke, velocity, over-travel, and contact wipe. Contactmotion analysis includes: Open, Close, Open-Close, Close-Open, and Open-Close-Open. The CT-6500 timing window is selectable: 1-second, 10-second, or 20-second periods. The 10 and 20-second timing windows allow timing the long duration events (Circuit-Switcher contacts). |
|
| VIC-DIGITIMR EHV Circuit Breaker Analyzer |
 |
|
- Stand-alone, microcomputer-driven EHV Circuit Breaker Analyzer
- Analyzes contact time, stroke, velocity, over-travel, and contact wipe.
- Computer Interface; 200-Shot EEPROM Storage
- Diagnostic ability
- Up to 45 breaker test plans can be stored
- Built-in Thermal Printer
|
The VIC-DigiTimr is a stand-alone, microcomputer-driven EHV Circuit-Breaker Analyzer. It is inexpensive and easy to use. The VIC-DigiTimr fully analyzes circuit-breaker performance: contact time, stroke, velocity, over-travel, and contact wipe. Contact-motion analysis includes: Open, Close, Open-Close, Close-Open, and Open-Close-Open. The VIC-DigiTimer timing window is selectable: 1-second, 10-second, or 20-second periods. |
|
| CT-7000/S2 Digital Circuit Breaker Analyzer |
 |
|
- Full Breaker Tabulated & Graphic Data Printout
- Detect Main & Insertion Resistor Contacts on same input
- Digital Travel Transducer; no setup or calibration needed
- Diagnostic ability
- USB and RS-232C computer interfaces
- Store 100 timing records and 99 test plans
- Initiate Breaker Operation
- Built-in Thermal Printer
|
The Model CT-7000 Series 2 is a third generation, stand-alone, microcomputer-driven EHV Circuit-Breaker Analyzer. It is inexpensive and easy to use. The CT-7000 is available in models with 3 dry contacts (CT7000-3), 6 dry contacts (CT-7000-6), or 12 dry-contact inputs (CT-7000-12). The CT-7000 fully analyzes circuit-breaker performance: contact time, stroke, velocity, over-travel, and contact wipe. Contact-motion analysis includes: Open, Close, Open-Close, Close-Open, and Open-Close-Open. The CT-7000 timing window is selectable: 1-second, 10-second, or 20-second periods. The 10-second and 20-second timing windows allow timing of long duration events (Circuit-Switcher contacts). |
|
| CT-7500/S2 Digital Circuit Breaker Analyzer |
 |
|
- On-Line Timing
- Capture First Trip Time
- Full Breaker Tabulated & Graphic Data Printout
- Built-in Thermal Printer
- Initiate Breaker Operation
- Digital Travel Transducer; No Setup or Calibration Required
- Support resistor type transducer
- Detect Main Contact and Insertion Resistor Contact on the Same Input Channel
- Store 100 records and 99 test plans
- USB and RS-232C computer interfaces
- Diagnostic Capabilities
|
The Model CT-7500 Series 2 is a stand-alone, microcomputer-driven EHV Circuit-Breaker Analyzer. Its inexpensive and easy to use. It operates in either of two modes: as a traditional Time-vs-Travel analyzer or as a Quick-Shot (on-line timing). In the Time-Travel mode, the CT-7500 analyzes breaker performance: contact time, stroke, velocity, over-travel, and wipe. Contact-motion analysis includes: Open, Close, Open-Close, Close-Open, and Open-Close-Open. The timing window is selectable: 1-second, 10-second, or 20-second periods. The 10-second and 20-second windows allow timing of long-duration events (e.g., circuit-switcher contacts). |
|
| CT-8000 Digital Circuit Breaker Analyzer |
 |
|
- On-Line Timing
- Capture First Trip Time
- Static & Dynamic Resistance Tests
- Full Breaker Tabulated & Graphic Data Printout
- Output Test Results to Built-in Thermal Printer
- Digital Travel Transducer; No Setup or Calibration Required
- Supports Resistance Type Transducers
- Detect Main Contact and Insertion Resistor Contact on the Same Input Channel
- Store 100 records and 99 test plans
- Computer Interface (RS-232C or USB)
|
The Model CT-8000™ EHV Circuit-Breaker Analyzer is a fifth-generation design configuration. The Model CT-8000 is a standalone,
microcomputer-controlled Circuit-Breaker Analyzer that is inexpensive and
easy to use. It operates in either of two modes: As a traditional Time-vs-Travel analyzer
or as a Quick-Shot (on-line timing). The CT-8000 is available with either 3
dry contacts (CT-8000-3) or 6 dry contacts (CT-8000-6) configurations. Both models are supplied with 3 digital travel transducer input channels. |
|
| CBPS-300 DC Power Source |
 |
|
- Built-in OPEN and CLOSE solid-state initiate circuit
- All DC outputs are over-current protected
|
The Model CBPS-300 is a microprocessor-controlled, variable-voltage, DC power supply. It is designed to replace substation batteries during circuit breaker testing. The CBPS-300 provides a ripple-free, DC power source to operate utility circuit breakers for contact-timing and other breaker-testing operations. |
|
| UPS Series 2 Universal Power Supply |
 |
|
- Isolated variable 1-300 Vdc source
- Isolated variable 1-240 Vac source
- 10 ampere continuous current
|
The Vanguard Universal Power Supply Series 2 (UPS-S2) is designed and produced to meet a utility company's substation needs for an independent AC/DC power source. Both the AC and DC Voltage sources are capable of supplying 10 amperes continuously.
The variable DC power supply (1-300 Vdc) is ideal for use as a substitute primary power source when station batteries are not available. The UPSS2 is ideal for operating circuit breakers, powering substation relays or for unregulated charging of substation batteries. The AC power supply is a variable isolated power source (1-240 Vac) that can be used to power other equipment in the substation. |
|
| MCCB-250 Molded Case Circuit Breaker Tester |
 |
|
- 4 current-shource outputs (i.e., 5 A @ 120 Vac, 25 A @ 24 Vac, 120 A @ 6 Vac, 250 A @ 3 Vac)
- 4-line by 20-character LCD display
- Provides external current input (0-10 A)
|
The VIC Model MCCB-250 is a programmable, high-current source designed specifically for testing molded-case circuit breakers, thermal magnetic and solid-state overload motor-protection relays. |
|
| Accessories for the CT-6500, CT-7000, and CT-7500 |
|
|
 |
|
